sobota, 27 kwietnia 2024

Napęd inercyjny

Napęd inercyjny, bezwładnościowy czy inaczej Inercoid, są to nazwy określające napęd, który nie potrzebuje paliwa, więc może działać w nieskończoność, a działa w oparciu o ruch materii, która generuje siłę odśrodkową, pęd albo nierównomierną reakcję na tej samej osi symetrii. W naszych czasach rozwój innych napędów niż rakietowe jest ograniczony w ogromnym stopniu a spalanie paliwa rakietowego jest z niewielkimi wyjątkami jedyną dostępną formą dostania się na orbitę okołoziemską i poza nią. Zaczynając od wieku dziewiętnastego, gdzie tworzone były podstawy współczesnej nauki, szczególnie fizyki teoretycznej, zabrakło bazy do wypracowania nowych kanonów naukowych, które dałyby początek takim technologiom jak napęd inercyjny. Z chwilą pojawienia się podstaw fizyki kwantowej oraz teorii względności, podstawy teoretyczne zaczęły dotyczyć jedynie zjawisk z zakresu grawitacji i elektromagnetyzmu, o inercji jednak przez długie lata milczano i nikt nie podnosił tematu, poza próbami opisu teoretycznego takich naukowców jak Ernst Mach, które jednak nie doprowadziły do jakiegokolwiek przełomu technologicznego w skali globu aż do dzisiaj. Obecne próby budowy urządzeń opartych o wykorzystanie napędu inercyjnego rozbijają się o brak finansowania, a zbudowane prototypy nie nadają się do praktycznego zastosowania, z nielicznymi zaprezentowanymi wyjątkami typu urządzeń Roberta Cooka, czy Roya Thornsona, gdzie ciąg wytworzony przekracza niekiedy 1 % masy urządzenia, jak w przypadku Cooka, czyli na sto kilogramów masy ciąg wynosi 1kg. 



W przypadku Inercoidu Szypowa ciąg wynosił 20 gramów na około 2,1 kg masy całego systemu. Napęd za pośrednictwem samej masy w obiegu zamkniętym wydaje się niemożliwy z uwagi na zasady dynamiki Izaaka Newtona, jednak prawa Newtona stosują się jedynie do układów, gdzie mamy do czynienia z dwoma ciałami, z których jedno jest odrzucane, by drugie mogło kosztem jego dynamiki nabrać prędkości, dobrze znana zasada akcji i reakcji, zasada działania rakiet i napędu odrzutowego, natomiast nic nie mówią o relacjach gdzie występuje jedno ciało, które się obraca po np. niesymetrycznej orbicie na jednej z osi symetrii lub występują dwa zsynchronizowane obiekty o przeciwnych kierunkach obrotu, znajdujące się odizolowanym układzie napędowym. Zasady napędu inercyjnego są w zasadzie dość proste. W skrajnych przypadkach napęd inercyjny może mieć znacznie większy potencjał wtedy ciąg przekracza ciężar urządzenia i całość staje się zdolna do oderwania się od podłoża, jednak są to przypadki które nie są obecnie nagłaśniane w mediach, gdyż zyskanie takiego ciągu zmienia postać rzeczy, całość staje się sensowna technologicznie, a więc może stać się konkurencją dla napędu rakietowego jak w przypadku urządzenia, które było prezentowane w Internecie przez Mike’a Marsdena i powtórnie na stronie Kelly Net oraz w serwisie YouTube. Jeżeli pogłoski o tym urządzeniu są prawdziwe, to świadczyłoby to sensowności prac nad tego rodzaju urządzeniami oraz udowadniałoby że napęd jest skuteczny. W Rosji jeszcze w latach siedemdziesiątych istniał naukowiec, który także interesował się napędem inercyjnym A. Tołczyn, opracowywał on urządzenia i mechanizmy, które działały z dość dużą efektywnością, istnieli też naukowcy o nazwisku Poliakow i Akimow, obaj interesowali się napędami inercyjnymi oraz polami inercyjnymi, jak również wirami ciekłej rtęci, skonstruowali oni urządzenie oparte na wirze rtęciowym, które w pierwszej fazie rozruchu generowało ciąg, który jednak zanikał podczas dalszej pracy urządzenia. Posiłkowali się oni pracami Wiktora Schaubergera, wynalazcy, który pracował w Niemczech podczas II wojny światowej. Skonstruował on szereg urządzeń opartych o efekty antygrawitacyjne w wirach wodnych, dzięki którym mógł budować pojazdy zdolne do lotu (Repulsine)


Repulsine

Jeżeli chodzi o obecną sytuację napędu inercyjnego w technologii, to nie jest ona dobra, nie inwestuje się w tego rodzaju koncepcje, a jeżeli się inwestuje to bardzo małe środki. Jednak rozwiązania napędu inercyjnego są obiecujące na przyszłość, wystarczy powiedzieć, że napęd jonowy generuje ciąg rzędu miliniutonów, delikatny podmuch jonów, podczas gdy obecne prace nad napędem inercyjnym doprowadziły do uzyskania 1 kg ciągu jak w przypadku urządzenia Cooka, przy ułamku środków zaangażowanych w budowę np. sondy Deep Space o napędzie jonowym. Trzeba by się zastanowić co byłoby bardziej korzystne dla cywilizacji, czy kontynuacja ścieżki i ulepszanie napędu rakietowego, czy pomyśleć całkiem o czymś innym jak napęd inercyjny. Rozwój koncepcji takich jak napęd inercyjny doprowadzić mógłby do radykalnych zmian w transporcie w obrębie Ziemi, gdyby współcześni posiadacze kapitału nie byli tak zapatrzeni w napęd o znikomych walorach użytkowych jakim jest niestety napęd rakietowy. Napęd inercyjny i magnetyczny działający na zasadzie wzajemnego oddziaływania pól, to nie jest mrzonka, wymaga on jednak wielu nakładów finansowych i woli do realizacji, by można było wycofać marnotrawione środki w technologii rakietowej, bo z tą technologią daleko nie zajdziemy. Gdyby udało się wprowadzić technologię opartą na samym polu magnetycznym, bądź polu magnetycznym i sile bezwładności można by już zapomnieć o rakietach i przystąpić do właściwego działania jakim byłoby opracowania systemów kolonizacyjnych w układzie słonecznym, do rzeczowej kolonizacji planet w systemie słonecznym. W społeczeństwach różnych państw pokutuje jednak przeświadczenie, że wszystko co nie wypluwa kupy dymu i ognia z dyszy nie nadaje się do eksploatacji kosmosu, napęd odrzutowy nie zapewni nam jednak sukcesu w pełnym wymiarze, a to że dotarliśmy do powierzchni księżyca używając jedynie napędu odrzutowego, jest ewenementem naszych czasów, i mamy poważny problem z ponowieniem tego wyczynu jak do tej pory. Inna sytuacja by była gdyby historia nie wymagała od ludzi takich karkołomnych działań, podyktowanych toczoną rywalizacją na arenie światowej, wyścigiem zbrojeń, wojnami zdegenerowanymi do morderczych kaźni wielu milionów ludzi, brakiem stabilizacji i pokoju między narodami, tak by współpracować a nie walczyć o wszystko z każdym. Wszystkim działaniom podejmowanym obecnie na arenie tej planety przez różne narody, przyświecał do tej pory jeden cel jakim było uzyskanie dominacji w gospodarce, nauce i stosunkach międzynarodowych, nie było myśli technicznej zmieniającej zasady gry w ogólnym wymiarze, nie doszło do konsolidacji działań o charakterze globalnym, sprzeczne interesy zdominowały stosunki międzynarodowe do tego stopnia że zablokowało to prace nad nowymi napędami, a obawy przed rozprzestrzenianiem nowych technologii bez kontroli przez chcących zachować dominację technologiczną narodów na świecie, skutecznie blokują prace nad nimi. Brak wspólnej polityki doprowadza świat na krawędź katastrofy i popycha do kolejnych konfliktów, świat robi się miejscem coraz bardziej niebezpiecznym do życia, a wprowadzanie takich systemów jak napęd inercyjny do powszechnego użytku w takiej sytuacji graniczy z nonsensem.




 

czwartek, 29 lutego 2024

Proxxon MF-70 mill - first works.

Machining of 1 mm thick brass plate with application of chuck dedicated for this device. Machining very easy with 2 mm mill cutter, even 2 mm thick brass would be not a problem. A lot of brass faint pieces around the mill is nothing strange. In assumption this part should be used as external rim after another machining process. I could use also the plate from the brass circle was made from.  












sobota, 30 grudnia 2023

Terrain propulsion.

Inertial railway propulsion with application of a couple of construction techniques seems to be plausible to build only with several assumptions which should be fulfilled to obtain measurable effects. The main assumption here is that the train will be affected by acceleration coming from gravity force from acting of the mass of entire planet once it will be located on a proper prepared track, that will be not parallel to earth surface thus it will be not curved with the proper curvature of the Earth. We should remember that almost entire infrastructure that is built by humans was constructed with respect to external curvature of Earth surface. Every object that is located on Earth surface is affected by gravity force and such a objects like liquids automatically are fitting to this curvature due to hydrostatic pressure created by gravity of the planet. Other objects created by humans must be curved due to their functionality for such a aims like railway and road transport. If for instance the railway was located on the straight line then on certain distance both ends of the train track would be placed on bigger and bigger distance from the ground and would need massive construction support. Straight line is possible to obtain with application of laser ray. This is only imaginary presentation and nobody would be able to build such a track on for instance ten thousand kilometers it is impossible from the technical side. However, with application of certain vibrational technics like vibration axial generators this system could work well on even very long railway track. In this case also both weight of entire train and inertia momentum on the longest axis is important. Application of axial vibration generators will allow to obtain high resonant frequency affecting the train suspended under the railway upper beams and the train should be moving on the track made from very hard reinforced concrete. Naturally, the question of half – usable driving force from the gravitation affecting the train is open, because when the train is on the minimal radius point the force from gravity after crossing that point would be acting in opposite direction and the train will be slowing down with the proportional force to the distance increasing on the other side of the balance system. What is more, if the train is approaching to the point of minimal radius the propulsive force will be decrease to minimal value what will be appear as lack of the ability to acceleration of the vehicle. So the train would be making further journey only thanks to gained earlier dynamic energy and even won’t arrive to its maximal radius point on the other side of the track. One should notice that the energy of force in entire system will be very low, and for the correct operation of the system the train will not be able to move up the hill or something like that. The other side of solving this problem would be dividing the track on shorter parts with more inclination, but then we are obtaining not straight line according to support beams location, and the ability of continuous movement of the train would be disturbed. Another approach to the matter is to notice one thing and this is the fact that if the object is falling in gravity field to the center of mass on the planet surface it has its own momentum and it will try to conserve its own independent trajectory without relation to external objects, so if it will fall on the earth surface it will be slightly displaced on the west after dropping from for instance high tower. This phenomenon can be used to the train propulsion to obtain forward movement in west direction and for this purpose can be used axial vibration generators, too. When the train is falling down lifted by those generators it will be falling down each time after generators stop, so it will be displaced a few micrometers ahead during the falling to the west direction but if to apply very fast vibrations those micrometers would be collected to kilometers as well, but this is only a uncertain prediction because I don’t know and can’t imagine what will happen when the train will be going to start position after falling down in gravity and whether this process won’t have contrary effect canceling the displacing obtained in the process of falling down. If the frequency of operation of entire system is to be great the free falling of the train mass will not be executable. Rather form of resonance will be involved into the system. So then the system will not be able to work on standard assumptions and one should consider what forces will be acting in the system in this case.





wtorek, 26 grudnia 2023

Oscylacyjny system napędowy

Dwie masy znajdujące się na oddzielnych wałach poruszające się ruchem wahadłowym generują siły odśrodkowe, które wywierają nacisk poprzez umieszczone od wewnątrz stojana magnesy stałe. Masy te mają możliwość naciskania na magnesy poprzez wzajemne siły magnetyczne, gdyż są one umieszczone a nie zamocowane w łożach o kształcie jak na tej animacji i znajdują się one blisko stojana więc odległość od magnesów wirników mass a magnesów stojana jest mała. Ruch tych mas jest zsynchronizowany, więc z każdym wychyleniem ich siły boczne są niwelowane a siła działająca i ciągnąca je do przodu pozostaje aktywna, a jest to siła odśrodkowa. W tym konkretnym rozwiązaniu występują inne siły inercyjne, które będą próbowały zniwelować siłę odśrodkową występującą w systemie, ale nie są one większe niż siły odśrodkowe w ogólnym wymiarze. W zasadzie do działania tego typu systemów potrzebne by było nie tyle rozwiązanie z zastosowaniem magnesów co, zastosowanie samych mas osadzonych na odpowiedniej długości wałkach i połączenie systemu z kołami zamachowymi oraz silnikami elektrycznymi z mechanizmem oscylacyjnym postępowo - powrotnym. Należałoby zastosować mały zakres wahania mass, by jak najbardziej wyeliminować wsteczne siły inercyjne osłabiające działanie sił odśrodkowych, zamiast tego system powinien oparty być o wysoką częstotliwość.


W tym przypadku jak na poniższej animacji amplituda drgań jest mniejsza, wyeliminowane zostały również magnesy.


System powinien działać z racy wolnej siły odśrodkowej występującej w kierunku ruchu systemu, nie jest to siła pchająca lecz ciągnąca, która jest tym większa im szybsze drgania oraz im masy są większe oraz ważne jest długość prętów na których jest zamocowana każda z mas. Problem powstających tutaj naprężenia zmiennego jest do rozwiązania pod względem technicznym, istnieje również problem zastosowania szybkiego mechanizmu zwrotnego.

niedziela, 5 listopada 2023

Drone.

This is a drone with centrifugal force distribution control. It is powered by three electric motors with gears. There are eight brass the same rollers in each generator. It looks good, but it will be requiring a lot of work to build it. I am going to mill proper parts on my milling machine immediately after i gain CNC possibilities with my machine, but it will be performed in small scale, with application of miniature DC motors and miniature ball bearings. I must buy a program to handle with the gcodes for the mill.




Video presenting the principle of operation of the single generator. 
 

Perspective view.


Up view


Side view


Side view







Alternative solution of rotor.





sobota, 23 września 2023

Minimal hop experiment and slip stick experiment.

I've decided to repeat my minimal hop experiment. I have built more accurate experimental set. I plan to connect the set to transformer which will be connected to home electricity net 230V 50 Hz. I will have an ability to control the gap in the system by application of brass or plastic washers in the case the gap would be too large for 50 Hz. I was trying to apply the square wave generator but after several seconds of working it was burned down. Within this term the system was tended to work correct, but with less force than I was predicted. The result was insufficient, so I decided to use a transformer, but I must accept the fact that I will not have an opportunity to control the work frequency of the system as I had in the case of the generator use. If the system will fall in correct vibration frequency it should loose half of its weight in each upper phase and gain 1,5 weights in every lower phase. Anyway, it should be able to move on table in vibrations. It should not levitate or something like that. It should move on vibration cushion. This system works only on single jump, but the magnet should fall after each up aimed movement. I will consider delivering the energy from a large condenser as a one-time discharge system, so I will obtain more energy in just one jump instead of application of vibrations obtained from application of transformer. However, this system needs underneath surface for take-off. I will be trying to make this system more independent. Maybe if I will manage to put together two such a systems, one on the upper side and the second on the bottom with equal the mass of permanent magnets, but on top I will mount a spring, so the one coil will be repeal and attract the magnets with respect to their polarization, so the system will be balanced but only according the mass, not a force which will be asymmetric thanks to application of short spring.  





Previous version video.




And this is another failed experiment I've conducted and if there is any upward force it is too weak to make a lift off the desk. So, this approach is incorrect due to wrong assumption that the system will be working right but in fact this system needs another material solution and some more advanced electronic control.  



wtorek, 12 września 2023

Centrifugal force manipulation using magnetic field.

I want to present magnetic force system which is predicted to change centrifugal force distribution with respect to direction of the device. This magnetic system is based on application of strong electromagnets which are mechanically joined with centrally located cross-shaped rotor and they are rotating with this rotor. The masses which are mounted on each arm of the central rotor have ability to move in its axis and in bottom position are retracted to the center of the system using magnetic attraction from electromagnets each time they are passing on lowest position of the device. This device doesn't need any external rim due to magnetic control of the system and escape prevention by using special construction of those masses and ends of the cross-shaped rotor. If the mass is passing in highest hemisphere of rotation it is on highest extension from the center, so centrifugal force is stronger than in bottom position. The masses are rotating fast in one direction, so they are changing with itself by positions. The electric current needed to electromagnets is delivered by commutator located on the main axis of rotation and each time the mass is on the bottom position is turning on to supply the bottom electromagnet. 






This simple drawing showing centrifugal force manipulation using magnetic field from electromagnets to make change in bottom position of mass (the mass is closer to center of rotation thanks attraction from electromagnets and extend more on the top, side masses don't matter).
System is mounted on external ring, and in a half a distance of this ring there is central shaft with ball bearings and with rotor. System is thought in such a way that should be working with high speed and with powerful electromagnets. This will allow to prevent the system from desynchronization due to centrifugal force, which is naturally stronger with greater speed of rotation. So, application of strong electromagnets is needed. If to applicate too weak electromagnets there could be such a situation that, due to centrifugal force, the electromagnets will not manage to retract bottom mass, so the system would be symmetrical in every direction ant that would mean that no result force would be generated. 




Old concept.




sobota, 26 sierpnia 2023

Comparison of two systems - G. Shipov inercoid and my own concept.

 The problem of inertial propulsion is based on manipulation of centrifugal force rarely by changing location masses in linear movement. That aim can be achieved by application of two ways, one is based on adding the mass in proper hemisphere of rotation and the second is based on changing the speed of rotation of those masses. Two rotating masses can cancel the problem of side centrifugal forces because they are paired. When the masses are located on the same side and not on opposite sides the force is occurring, differently to the situation in which they are located on opposite sides if they are synchronized the force is equal zero. In Inercoid of G. Shipov they are forced to moving faster in forward part of the circumference and they don't touch external rim (there is no external rim at all in this case) thus don't need any bearings, different power is used from the DC motors to propel them faster in forward and slower in rear part of the system.  


In my solution the system is working more liquidly, however require bearings (linear and ball bearings). My system is based on application of special rim located on the outside and its curvature, which is limiting escape of the masses due to centrifugal force. So, the system operation is based only on the same current, no change in voltage is needed supplying the DC motor nevertheless the motor will get more voltage on continuous speed up needed to gain more propulsive force. Changing in speed is caused only by this curvature and the changed in time distance between the mases and the center of rotation. If the massed are close to the center of rotation the centrifugal force is falling also to almost zero, due to the minimal road to go for the masses. If the masses are passing in highest point of the system, they also have a potential in centrifugal force strength implicating from faster movement on more distant orbit around the center point of rotation.





Magnetic rotor with circumference magnets.

A magnetic device based on attraction between circumference permanent magnets and outside magnet - rim also made from permanent magnet or soft steel. The rest of work are making the springs, which are trying to attract each permanent small magnet to the center of the rotor, but not exactly because there is certain distance between linear force created by each spring and the geometric center of the system, and the force axis are not passing through the exact center of the device thus the vectors are omitting that center what. The result is that the system is not balanced mechanically, because none of vectors coming from the springs is acting on the same straight line. This system is asymmetric in every cross section in the perpendicular ax of this drawing plane. I'm not completely sure whether the device would be working as I want, and it was not tested due to my low skill in machining and low knowledge in such a devices operation principle. The circumference magnets which are sliding from the inside on the outside rim should be mounted on ball bearings. However still, there is the possibility, that the device will not be working, and the system will be balanced right after the setting up moment. For this problem is only one solution and this is to build the prototype, however some of people could also try to calculate whether the device will be working if they own a proper software. I was trying to imagine the working of this device many times, sometimes it was seemed to me that the device will be working fine, and sometimes that it won't work correctly due to forces will be balanced automatically. So, if someone have a proper software than after loading this data to the program will be able to check this problematic for me system out. Like many other magnetic motors this system is also controversial. I posted it here because I am interested of generating electric energy without burning fuel and I am aware of the danger coming from application of nuclear energy also other energy sources are not safe for our civilization, so searching for the new source of generating energy seems to be very reasonable right now.

 

niedziela, 13 sierpnia 2023

Roy Thornson based system.

Roy Thornson has invented inertial propulsion with two weights rotating on inner static gears. Those weights were mounted on the same gear in dimension and the gear with the weights were rotating on the circumference of the static gears, which were inside. In some analyses there was indicated that Thornson drive is working correctly and there were experiments with this dive based on mounting a propulsion unit on a bout in swimming pool. Analyses and experiments have clearly indicated that propulsions are effective. I've decided to visualise the principle of working of this propulsion and I have made some animations on 3D software. This simple principle of operation is based on applying synchronization of rotating gears in this way that the weight attached to one gear is hidden on bottom side and is extending on the outside on top part of the device. Such a behavior of mechanism is based on proper application of gears and creating the proper distance between main shaft and dimension of the caring rotor; thus, the weight can pass inside two free spaces in this rotor rotating on its own axis of rotation. The weight is mounted on roller or ball bearings also the main shaft is mounted on the bearings. Additionally in the static gear there is a hole making available of passing the thin part of the main shaft inside. The static gear is attached to external rim so it can't rotate. The paired system is also shown at the bottom for making balance of the system. However, system can generate a lot of vibration due to not balanced centrifugal force at the bottom of the device. The side centrifugal forces will be cancelled by self-balancing of the system due to system can be paired.


  





sobota, 15 lipca 2023

Magnetic propulsion from copper rotating discs and electromagnets.

That's how I imagine a magnetic propulsion. It is simply magnetic slowing down rotating copper discs and, in this process, the inertial energy of the discs and magnetic power from the electromagnets will, as I suspect, change to linear upward thrust. As I said those copper discs have horseshoe electromagnets, and they are passing between those electromagnets. The device will be propelled by three electric motors. Each from the three generators is mounted on two ball bearings which are not shown in the pictures. In earlier attempts of this idea, I was proposing the application of permanent magnets placed on near to the disc's circumference distances and this could be in my opinion better solution due to avoiding strong overheating the copper discs in this solution as it is shown on my pictures, however I was trying to simplify a little my conception so I am posting the method with copper discs without the magnets. The system can simply not work due to this device stands one piece and the forces can balance each other. I have noticed earlier this problem, so I simultaneously have developed the system where copper core was rotating in non-ferromagnetic tube pushed by compressed air so the system will be divided to two different parts to avoid self-balancing of the forces. So, I am aware that system I'm presenting right now could have key defects making unavailable correct working of such a device but also want to share my thoughts to wider publicity to show my progress in research in the magnetic propulsion. How about connecting those discs to electric current. If the current will flow from the center to the circumference of the discs or in opposite direction than the Lorentz force could appear with interaction between current and magnetic field from the electromagnets. Additionally electric charge in movement will produce the magnetic force that would be interacting with electromagnets. However, complexity of such a solution where I have rotating discs with flowing current and magnetic field from the electromagnets makes me a little dizzy this time. Maybe someone with better mind could solve this problematic situation with this technology attempt. 



This technology needs an approach where knowledge from the range of magnetic field and electric current takes the main place. If the current will be predicted to flow from the inside of the discs to the circumference with perpendicular magnetic field application with use of electric brushes than magnetic field from flowing charge discs will be interacting with electromagnets. 




Eight steel ball experimental set with trouble.

I have added 2D drawings for eight ball eccentric system. This system will be probably working only for couple of whiles next it will burn d...